SEACLEAN Supplier & Exporter

Intense SOLVENT BASED CLEANING AGENT FOR TANK CLEANING AT SEA
PHYSICAL DATA
Appearance: Clear golden fluid
Obvious Specific Gravity: 0.90 at 20°C
Streak Point: More than 70° C (158° F)
Destructive activity:
Metals and Coatings: None
Elastic: Slight swelling
Solid emulsifying cleaning operator for the evacuation of overwhelming raw petroleum, ash, black-top and carbon dark stains, by coordinate infusion, ocean clean strategy, showering and additionally distribution technique. In light of aliphatic/fragrant hydrocarbons and non-ionic/anionic surface dynamic specialists. Washing times are diminished by half and just slight fomentation is ordinarily required. The item is protected to use on normal metals.
APPLICATIONS
Tanks
SEACLEAN can be utilized for the expulsion of most mineral oils and fats in load and capacity tanks.
Twofold Bottom Tanks
SEACLEAN can be utilized for cleaning and gas liberating of Double Bottom Tanks. Utilizing the moving movement of the ship will ordinarily give adequate disturbance.
Bearings FOR USE
Cleaning of Cargo and Storage Tanks:
Pre-wash
Before cleaning with SEACLEAN, it is prescribed to prewash tanks with heated water of around 50°C aside from unrefined petroleum,
drying and semi-drying oils where a prewash with chilly water ought to be connected.
Coordinate Injection Method for Cargo Tanks
SEACLEAN ought to be infused at a foreordained rate into the weight side of the programmed tank cleaning framework line on deck by methods for an air-worked drum (barrel) pump. Normally an infusion rate of 0.1 0.2 liter SEACLEAN per 100 liters of tank wash water is adequate. Cleaning time 2-6 hours. In this manner wash with water.
 
Hand Spraying Method
SEACLEAN on to bulkhead, outlines, stringers, longitudinals and so on utilizing an air-worked drum direct associated with a conveyance hose and hand shower weapon. After a foreordained response time, tanks ought to be washed with water utilizing the programmed tank clothes washers. For spot cleaning just, utilize hand held hose for flushing, for example a firehose with spout. Hand Spraying Method is the most prudent framework as far as concoction utilization yet requires tanks beeing gasfree empowering men to enter tanks. In any case, Hand Spraying Method has a functional time impediment relying upon tank sizes, i.e. add up to tank surface to be showered.
 
Distribution Method
A compound arrangement is set up in one of the after tanks close to the pump room, coursed by means of the programmed tank washing framework pump furthermore, warmer to the tank to be cleaned, wherefrom the arrangement is come back to the compound arrangement tank by means of the stripping line. For the most part it isn't conceivable to recycle arrangement through the tank washing framework warmer (to keep up arrangement temperature) without making a brief association between the synthetic arrangement tank and the tank washing pump. Limits of arrangement tank, pipelines and pumps and so forth ought to be ascertained precisely to guarantee adequate volumetric amount for a constant distribution. Contingent upon size and state of tanks to be cleaned and amount of substance arrangement, a disadvantage in this technique is that more often than not just 3 (three) tanks can be cleaned with one arrangement after which a new arrangement ought to be made and warmed before cleaning can proceed. The required arrangement quality is 2-6% SEACLEAN. After concoction cleaning the tanks ought to be washed altogether with ocean water or new water contingent upon accessibility and prerequisites.
 
At Sea Cleaning Method: (Double Bottom Tanks)
Time, temperature and disturbance of compound arrangement are critical components for the effective cleaning of Double Bottom Tanks.
 
Methodology:
1. Warmth tank to higher than ordinary temperature, draw out however much fuel as could be expected and trim vessel to guarantee
 
finish stripping.
2. Close all valves on motor room complex.
3. Present first measurements of SEACLEAN, through the sounding funnel, as per the dose table expressed beneath and fill the tank to 25% of its ability with ocean water. For filling the tanks it is prompted not to utilize the weight lines as they may contain fuel oil making the cleaning more troublesome.
4. Warmth cleaning answer for least 60°C and keep up temperature for 48 hours. On the off chance that warming loops are not profit capable, live steam might be utilized for warming the arrangement and look after temperature.
5. Exhaust tanks totally, completely fill and purge once more. Where single stage cleaning is utilized the previous steps are overlooked.
6. Include second dosage of SEACLEAN and fill tank with ocean water to half of it's ability, keep warming and keep up at this level for 48 hours.
7. Add encourage ocean water to completely fill tank, keep warming and keep up for an additional 48 hours.
8. Purge tanks and weight flush with clean water through sounding channels for 1-1 hour under nonstop stripping. Weight ought to be kept as high as security grants. 9. When washing is finished stop release (stripping) pump and fill tank until the point when clear water keeps running from sounding pipes on deck.
10. Stop water supply and discharge (strip) tank. Trim vessel to guarantee finish stripping.
 
Dealing with and capacity
Store in a very much ventilated place, keeping the compartments shut when not utilized.
Try not to smoke while dealing with. Keep far from wellsprings of warmth, splendid flares
what's more, sparkles and different wellsprings of start.
Dubichem chemicals international is a leading supplier, manufacturer and exporter of SEACLEAN in Dubai, Ajman, Abu- Dhabi, Sharjah, Fujairah, Turkey, Saudi Arabia, Qatar, Kuwait, United Arab Emirates, Oman, Singapore, Malaysia, Indonesia, Lebanon, Greece, India, Sudan, Ghana, Madagascar, Kenya, Nigeria, Zimbabwe, Uganda, Ethiopia, Namibia, Mauritius, South Africa ,Europe & Globally for any queries mail us at dubichem@gmail.com and for more related products visit www.dubichem.com